1 mm = 0.04 inch 1 inch = 25.4 mm horizontal vertical for panel mounting 2,5 14,4 al 0,25 5,5 0,7 5 m6 x 0,75 description bcd-, hex or gray coding. shorting or non-shorting switch mode. horizontal or vertical verison. operation by screwdriver or stainless steel shaft (knob). sealed and washable rotation with positive detent setting solid tinned terminals (0,4 x 0,7 mm) terminations for direct mounting on circuit boards 2.54 mm (0.1'') pitch indexing positions, end stop according to the code 16 resp. 10 positions with stop between the first and last position or without stop setting reflow version available on request horizontal for panel mounting front-panel operation 5 2,5 8 al 0,25 5,5 0,7 m6x0,75 vertical 2,25 12,7 10,6 al -0,25 3,1 10,16 10,16 1c4 2c8 ?5,5 ?3 0 bcd 18 hex 1115' 5,08 1,1 2,3 ?8,6 13,67 0 1c4 front-panel cut out 5d11 6d11 5d11 6d11 front-panel cut out drilling diagram view from component side ?0,9 1 c 4 82 2,54 2,54 5,08 ?0,9 1 c 4 28 2,54 2,54 12,7 drilling diagram view from component side coded switches type 07 5,08 1,1 2,3 7.59 ?8,6 13,77 ?5,5 ?3 0 4,17 al- 0,25 2,25 10,35 0 10,16 bcd 18 hex 11 15' 10,5 3,1 5,42 3 1c4 1c 4 standard: al=12,8mm / max. 30mm standard: al=12,8mm / max. 30mm standard: al=11,5mm / max. 26mm standard: al=11,5mm / max. 26mm panel mounting waterproof o-ring and nut supplied panel mounting waterproof o-ring and nut supplied 60
61 1 mm = 0.04 inch 1 inch = 25.4 mm coded switches type 07 mechanical data indexing mechanism 36 = 10 positions (bcd) 22 30' = 16 positions (hex and gray code) switching torque 2,2 ncm 25% (bcd) 3,2 ncm 25% (hex and gray code) max. force on the end-stop 45 ncm (bcd) 35 ncm (hex and gray code) panel mounting admissible torque max. 100 ncm temperature range storage temperature: ? 40 c to + 85 c operating temperature: ? 25 c to + 85 c vibration resistance 10?2000 hz/10 g life >10000 switching cycles (>200000 switching positions bcd) (>320000 switching positions hex or gray) technical information material data case high quality temperature-resistant thermoplastic spindle-shaft stainless steel insulation high quality thermoplastic contact parts alloy copper > 3 m gold plated soldering data handsoldering plastic wafer 5 s/ 260 c machine soldering wave 5 s/ 260 c reflow (thr) 5 s/ 260 c (on request) lead free reflow (on request) electrical data application data voltage < 42 v current < 0.2 a switching capacity 5 va switching voltage 42 v (resistive load) switching current 0,2 a (resistive load) test voltage at 50 hz/i min 500 v ~ insulation resistance at 500 v = 1 min 10 11 ? contact and lead resistance < 50 m ? in new condition various assembled in cleanroom class 100 000, us federal standard sealed and washable ip protection degree sealable up to ip 68 (2bar) coding bcd 2 3 2 2 2 1 2 0 0 1 ? 2 ? 3 ?? 4 ? 5 ?? 6 ?? 7 ??? 8 ? 9 ?? bcd complem. 2 3 2 2 2 1 2 0 0 ???? 1 ??? 2 ?? ? 3 ?? 4 ??? 5 ?? 6 ?? 7 ? 8 ??? 9 ?? hex 2 3 2 2 2 1 2 0 0 1 ? 2 ? 3 ?? 4 ? 5 ?? 6 ?? 7 ??? 8 ? 9 ?? a ?? b ??? c ?? d ?? ? e ??? f ???? hex complem. 2 3 2 2 2 1 2 0 0 ???? 1 ??? 2 ?? ? 3 ?? 4 ??? 5 ?? 6 ?? 7 ? 8 ??? 9 ?? a ?? b ? c ?? d ? e ? f gray code 2 3 2 2 2 1 2 0 0 1 ? 2 ?? 3 ? 4 ?? 5 ??? 6 ?? 7 ? 8 ?? 9 ?? ? a ???? b ??? c ?? d ??? e ?? f ?
62 1 mm = 0.04 inch 1 inch = 25.4 mm ordering an option to order a special option please use the order form. please specify your requirements and send it to your local contact or to elma. standard: al = 11,5 mm max. 26 mm front panel cut out switch on pos. 0 0,7 b special options type 07 special shaft length please state length al (see diagram) measured from mounting face when ordering (max. al = 30 mm) specify shaft length on order form. panel mounting/waterproof version m6 x 0.75 the threaded bushing is made of die cast allows (2,5 m tin plated, chromate fi nish) for enviromental protection such as salt fog exposure. max. admissible tightening torque for nuts 100 ncm (~10 kp cm) order example zb (panel mounting) zb/wd (panel mounting and waterproof) waterproof 2 bar (ip 68) standard, (higher level on request) please complete order form. adjustable stops (internal stop) adjustable stops can be set during assembly on all switch positions between 1 and 16, e. g. coded output 0 to f. adjustable stop settings which do not start from coded output 0 ( e. g. 3?6) are available on request. please complete order form. special type of shaft specially machined shafts are available. please attach a sketch or drawing to your order. specify dimensions on order form. shortened bush please state dimension b dimension b = min. 3,5 mm / max. 5,5 mm specify dimensions on order form. standard bcb 18 hex 1115? standard: al = 12,8 mm max. 30 mm panel mounting waterproof o-ring and nut supplied
63 1 mm = 0.04 inch 1 inch = 25.4 mm switch type 0 = horizontal (screwdriver actuation) 1 = horizontal with shaft 2 = vertical (screwdriver actuation) 3 = vertical with shaft 4 = horizontal fks (front panel operation) 0 = endless rotation 1 = with end stop 3 = bcd 4 = bcd ? compl. 5 = hex 6 = hex ? compl. 7 = gray-code 3 = shorting 4 = non-shorting 0 7 ? x x x x ? x x x x x x this code specifies the function of the switch bg = special end stop al = shaft length zb = panel mounting wd = waterproof fks = front panel operation ordering code to type 07 0 = standard e = bg 15 pos. 0 ? e d = bg 14 pos. 0 ? d c = bg 13 pos. 0 ? c b = bg 12 pos. 0 ? b a = bg 11 pos. 0 ? a 9 = bg 10 pos. 0 ? 9 8 = bg 9 pos. 0 ? 8 7 = bg 8 pos. 0 ? 7 6 = bg 7 pos. 0 ? 6 5 = bg 6 pos. 0 ? 5 4 = bg 5 pos. 0 ? 4 3 = bg 4 pos. 0 ? 3 2 = bg 3 pos. 0 ? 2 1 = bg 2 pos. 0 ? 1 (bg = special end stop) 00 = standard 20 = zb (panel mounting) 30 = zb / wd (panel mounting/waterproof) ? = standard v = anti-static package t = 3,5 ncm torque s = 3,5 ncm torque and anti-static package 000 = standard al 12,8 panel mounting al 11,5mm xxx = al (shaft length) z. b. al 10,5 mm = 105 options options
64 1 mm = 0.04 inch 1 inch = 25.4 mm order form for special options for coded switches type 07 special shaft length special shaft length for panel mounting ?3 min. 3 2,25 al 0,25 ?3 min.1 al 0,7 0,25 0,1 0,1 0 2 al standard 12,8 mm, max. 30 mm al standard 11,5 mm, max. 26 mm switch in pos. 0 machined shaft b standard 5,5 min. 3,5 max. 5,5 (drawing is valid for horizontal and vertical version) company customer no. address phone name fax e-mail quantity requested delivery date similar to order no. function bcd bcd compl. (indexing angle 36) hex hex. compl. (indexing angle 22,5) gray code (indexing angle 22,5) shorting special stop non-shorting from position to position horizontal version switching torque standard bcd 2,2 ncm vertical version standard hex. 3,2 ncm special bcd/hex. 3,5 ncm with shaft without shaft front panel operation (fks) panel mounting m6 x 0,75 (zb) waterproof version (zb/wd) ip protection degree.................... copy ? fill in ? fax quote request order sketch (additional technical requirements / comments) 0,1 0,5 standard bcd 18 hex 1115? max. 4 mm
|
